Deprecated: Creation of dynamic property cls_session::$session_data_table is deprecated in /www/sites/www.188bio.com/index/systems/cls_session.php on line 49
Cytoskeleton/Tubulin protein (97% pure): porcine brain/1x4 mg/HTS03188bio精品生物—专注于实验室精品爆款的电商平台 - 蚂蚁淘旗下精选188款生物医学科研用品
您好,欢迎您进入188进口试剂采购网网站! 服务热线:4000-520-616
蚂蚁淘商城 | 现货促销 | 科研狗 | 生物在线
产品资料

Cytoskeleton/Tubulin protein (97% pure): porcine brain/1x4 mg/HTS03

Details

Product Uses Include

  • Economical alternative to T240 in primary screens for tubulin ligand drugs
  • High-throughput tubulin polymerization or depolymerization screens
  • Production of microtubule substrates for HTS motor assays

MaterialTubulin protein has been isolated from porcine brain. The final product contains approximately 97% tubulin and 3% Microtubule Associated Proteins (MAPs). This version of porcine tubulin is an economical alternative to our highly purified tubulin (Cat. # T240) for anti-tubulin ligand drug discovery. It has been formulated to be compatible with 96 or 384-well format polymerization assays such as in Biochem™ kits BK004P or BK011P .

PurityProtein purity is determined by scanning densitometry of Coomassie Blue stained protein on a 12% SDS-PAGE gel. HTS02 contains 97% tubulin (MW. 55 kDa) and 3% MAPs (MW 35-280 kDa).

hts02

Figure 1: A 100 µg sample of HTS03 protein was separated by electrophoresis on a 12% SDS-PAGE gel and stained with Coomassie Blue. Protein quantitation was performed using the Precision Red Protein Assay Reagent (Cat.# ADV02).

Biological ActivityAn ASSAY UNIT is defined as the amount of HTS03 protein needed to achieve a tubulin polymerization signal of OD340 of 0.1 - 0.15 in 30 minutes at 37°C in G-PEM buffer. The assay volume is 100 µl and assumes a spectrophotometer pathlength of 0.5 cm. The protein concentration for HTS02 in this assay is approximately 4 mg/ml. The biological activity of HTS03 is assessed by a tubulin polymerization assay. One ASSAY UNIT of tubulin is used for each polymeriztion assay. An OD340 of 0.10 - 0.15 is required to pass quality control. Tubulin polymerization must also be responsive to polymerization enhancers (paclitaxel) and inhibitors (nocodazole) at 5 µM drug concentration.

CDS01res

Figure 2: Tubulin polymerization in a 96-well format using HTS03. All samples are in duplicates. Each well has a mini-polymerization curve with 20 min on the x-axis and 0.30 OD 340 nm on the y-axis. The Vmax parameter is used to compare inhibitors, the CV is 13% in this format, so a 50% cut off is required for a 98% confidence.

About

For product Datasheets and MSDSs please click on the PDF links below. For additional information, click on the FAQs tab above or contact our Technical Support department at tservice@cytoskeleton.com

Citations

Li et al., 2012. Orally Bioavailable Tubulin Antagonists for Paclitaxel-Refractory Cancer. Pharm. Res. DOI: 10.1007/s11095-012-0814-5.

Also, see references for Cat. # BK004P which uses HTS03 for the tubulin source

Faqs

Question 1: Does tubulin polymerization using 97% pure porcine brain tubulin (Cat. # HTS03) require additional enhancers such as glycerol or taxol?

Answer 1: No additional enhancers are required when using 3 or 4 mg/ml of the MAP-enriched 97% pure tubulin. The recommended polymerization reaction using 97% pure tubulin contains 100 μl of 3 or 4 mg/ml tubulin in 80 mM PIPES pH 6.9, 0.5 mM EGTA, 2 mM MgCl2 and 1 mM GTP. Polymerization is started by incubation at 37°C and followed by absorption readings at 340 nm. Under these conditions, polymerization will reach a maximal OD340 between 0.15 – 0.25 within 30 minutes. In this experimental set up (100 μl volume in a spectrophotometer with a pathlength of 0.5 cm), an OD340 of 0.1 is approximately equal to 1 mg per ml of tubulin polymer mass. Under these conditions only 40% of the tubulin is polymerized, offering the flexibity to study how polymerization enhancers (e.g., taxol) or inhibitors (e.g., nocodazole) alter tubulin polymerization. For enhancers, we recommend using 3 mg/ml tubulin whereas for inhibitors, 4 mg/ml tubulin works better.

Question 2: Upon resuspension as directed, what are the components of the final buffer?

Answer 2: Upon reconstitution as directed, the tubulin will be in the following buffer: 80 mM PIPES, 1 mM EGTA, 1 mM MgCl2, pH 7.0, 1 mM GTP, 1% Ficoll, 5% sucrose and <1mM DTT.

If you have any questions concerning this product, please contact our Technical Service department at tservice@cytoskeleton.com

新闻动态
行业前沿
技术文章
最新产品